features formerly model six windings - multiple con gurations compact size tape and reel packaging rohs compliant* applications inductors: buck-boost, coupled, ltering, common mode transformers: flyback, push-pull, inverter, gate drive, isolation pm600/pm610/pm620 series - smd inductor/transformer *rohs directive 2002/95/ec jan. 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. *rohs compliant electrical speci cations general speci cations rated current ....... ind. drop of 30 % typ. ...................................................at isat temperature rise ... 40 ? typical at irms operating temperature ................................ -40 ? to +105 ? storage temperature ................................ -40 ? to +105 ? soldering .......... 245 ?, 5 seconds max. dielectric strength ................... 500 vrms between windings materials core .............................................. ferrite wire ........... polyurethane-coated copper terminal coating............. sn-ag-cu alloy packaging pm600 ..........600 pcs. per 13-inch reel pm610 ..........300 pcs. per 13-inch reel pm620 ..........200 pcs. per 13-inch reel bourns part no. inductance 100 khz dcr ( ) max. isat (a) irms (a) <1> et (vms) based on 40 ? rise (260 khz) <1> et (vms) based on core saturation ( h) tol. (%) pm600-01-rc 201.6 ?0 0.324 0.02 0.46 16.8 103.2 pm600-02-rc 89.6 ?0 0.137 0.03 0.71 11.2 68.8 pm600-03-rc 27.4 ?0 0.324 0.31 0.46 16.8 103.2 pm600-04-rc 12.2 ?0 0.137 0.47 0.71 11.2 68.8 pm600-05-rc 14.7 ?0 0.324 0.58 0.46 16.8 103.2 pm600-06-rc 6.5 ?0 0.137 0.87 0.71 11.2 68.8 pm600-07-rc 10.9 ?0 0.324 0.88 0.46 16.8 103.2 pm600-08-rc 4.9 ?0 0.137 1.32 0.71 11.2 68.8 pm600-09-rc 8.5 ?0 0.324 1.23 0.46 16.8 103.2 pm600-10-rc 3.8 ?0 0.137 1.85 0.71 11.2 68.8 pm610-01-rc 160.0 ?0 0.202 0.04 0.68 21.0 130 pm610-02-rc 78.4 ?0 0.094 0.06 1.00 14.7 91 pm610-03-rc 21.6 ?0 0.202 0.67 0.68 21.0 130 pm610-04-rc 10.6 ?0 0.094 0.96 1.00 14.7 91 pm610-05-rc 11.6 ?0 0.202 1.30 0.68 21.0 130 pm610-06-rc 5.7 ?0 0.094 1.86 1.00 14.7 91 pm610-07-rc 8.3 ?0 0.202 2.00 0.68 21.0 130 pm610-08-rc 4.1 ?0 0.094 2.86 1.00 14.7 91 pm610-09-rc 6.6 ?0 0.202 2.30 0.68 21.0 130 PM610-10-RC 3.2 ?0 0.094 3.29 1.00 14.7 91 pm620-01-rc 160.6 ?0 0.094 0.03 1.28 20.8 130 pm620-02-rc 77.0 ?0 0.065 0.04 1.54 14.4 90 pm620-03-rc 131.8 ?0 0.094 0.08 1.28 20.8 130 pm620-04-rc 63.2 ?0 0.065 0.12 1.54 14.4 90 pm620-05-rc 23.3 ?0 0.094 0.36 1.28 20.8 130 pm620-06-rc 11.2 ?0 0.065 0.52 1.54 14.4 90 pm620-07-rc 14.2 ?0 0.094 0.76 1.28 20.8 130 pm620-08-rc 6.8 ?0 0.065 1.10 1.54 14.4 90 pm620-09-rc 9.3 ?0 0.094 1.11 1.28 20.8 130 pm620-10-rc 4.5 ?0 0.065 1.60 1.54 14.4 90 pm620-11-rc 7.9 ?0 0.094 1.40 1.28 20.8 130 pm620-12-rc 3.8 ?0 0.065 2.02 1.54 14.4 90 <1> single or multi-windings in parallel. et of multiple winding in series is number of windings times value of et.
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. pm600/pm610/pm620 series - smd inductor/transformer typical con gurations basic diagram inductance: current: inductor: l i figure 1 inductance: current: 36 x l i figure 2 inductance: current: 25 x l i figure 3 inductance: current: 16 x l i figure 4 inductance: current: 9 x l 2 x i figure 5 inductance: current: 4 x l 3 x i figure 6 inductance: current: l 6 x i basic diagram turns ratio: 1:1:1:1:1:1 transformer: figure 1 turns ratio: 1:1 figure 2 turns ratio: 1:1:1 figure 3 turns ratio: 1:5 or 5:1 figure 4 turns ratio: 1:4 or 4:1 figure 5 turns ratio: 1:3 or 3:1 figure 6 turns ratio: 1:2 or 2:1 figure 7 turns ratio: 4:1:1 figure 8 turns ratio: 3:1:1:1 figure 9 turns ratio: 2:3 or 3:2
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. pm600/pm610/pm620 series - smd inductor/transformer product dimensions 1 6 12 4 1 7 pm600-01 5 2 6 3 10 7 11 8 12 9 9.2 (.362) 11.0 (.433) 12.2 (.480) 10.0 (.394) 13.2 (.520) mark pin #1 pad layout pm600 series schematic 2.0 (.079) 0.25 (0.01) 0.7 (.028) typ. typ. 2.0 (.079) 1.0 (.039) typ. typ. 12.7 (.500) 6.2 (.244) max. 4 1 5 2 6 3 10 7 11 8 12 9 schematic 13.6 (.535) 17.0 (.669) pad layout 2.5 (.098) 1.5 (.059) typ. typ. 1 6 12 7 pm610-01 mark pin #1 pm610 series 2.5 (.098) 0.7 (.028) typ. typ. 15.0 (.591) 7.8 (.307) max. 12.0 (.472) 14.6 (.575) 16.0 (.623) 0.35 (.014) 1 6 7 12 schematic pad layout 17.1 (.673) 22.4 (.882) 2.5 (.098) 1.5 (.059) typ. typ. 1 6 12 7 pm620-01 mark pin #1 pm620 series 2.5 (.098) 0.7 (.028) typ. typ. 17.0 (.669) 8.4 (.331) max. 15.0 (.591) 18.1 (.713) 21.4 (.843) 0.40 (.016) dimensions: mm (inches)
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. pm600/pm610/pm620 series - smd inductor/transformer packaging speci cations 16.22 0.10 (.639 .004) 24.00 0.10 (.945 .004) 13.00 0.10 (.512 .004) 16.00 0.10 (.630 .004) 0.30 (.012) max. r 1.50 +0.10/-0.00 (.059 +.004/-0.00) 1.50 +0.10/-0.00 (.059 +.004/-0.00) 2.00 0.10 (.079 .004) 0.40 0.05 (.016 .002) 0.35 (.014) 4 plcs. 2.00 (.079) 0.50 (.020) r min. dia. 4.00 0.10 (.157 .004) .040 0.05 (.016 .002) 2.00 0.10 (.039 .004) 1.50 (.049) min. dia. 1.70 +0.15/-0.05 (.067 +.006/-0.00) 1.75 0.10 (.069 .004) 1.75 0.10 (.069 .004) 16.22 0.10 (.639 .004) 28.40 0.10 (1.118 .004) 32.00 0.30 (1.260 .012) 1.50 +0.10/-0.00 (.059 +.004/-0.00) 6.30 0.10 (.248 .004) 10 10 10 10 10 10 10 10 13.00 0.10 (.512 .004) 11.50 0.10 (.453 .004) 24.00 0.30 (.945 .012) 14.20 0.10 (.559 .004) 8.65 0.10 (.341 .004) 4.00 (.157) 4 plcs. 4.00 0.10 (.157 .004) pm600 pm610 dimensions: mm (inches)
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. pm600/pm610/pm620 series - smd inductor/transformer packaging speci cations (continued) dimensions: mm (inches) 17.00 0.10 (.669 .004) 28.00 0.10 (1.102 .004) 1.50 +0.10/-0.00 (.059 +.004/-0.00) 3.00 (.118) 2.00 0.15 (.079 .006) 0.45 0.05 (.018 .002) 1.75 0.10 (.069 .004) 22.50 0.10 (.886 .004) 6 20.20 0.15 (.795 .006) 40.40 0.30 (1.732 .012) 44.00 0.30 (1.732 .012) 5 40 9.10 0.10 (.358 .004) 4.00 0.10 (.157 .004) pm620 0.50 (.020) r 0.30 (.012) r 0.75 (.030) r 1.70 +0.15/-0.05 (.067 +.006/-0.00) 1.50 +0.10/-0.00 (.059 +.004/-0.00) 40 w1 w1 pm600 pm610 pm620 w2 w2 2.0 0.5 (.079 .020) 30.4 (1.197) 26.0 (1.024) 50.0 (1.969) 330 (12.99) dia. 13.0 ?0.5 (.512 ?.020) dia. 13.0 ?0.5 (.512 ?.020) dia. 21.0 0.8 (.827 .031) 38.4 (1.512) 34.0 (1.339) 50.4 (1.984) 46.0 (1.811) embossed carrier embossed cavity 0.10 (.004) max. thickness <1> single or multi-windings in parallel. et of multiple winding in series is number of windings times value of et. rev. 06/08
|
